ITEM	Standard test Method	ASTM Spec	Conductive Tile
ELECTRICAL / ELECTROSTATIC PROPERTIES
Electrical Resistance -Surface to Surface -Surface to Ground	ESD S 7.1 (100V / 10V) ASTM F-150 (100V / 10V) NFPA 99 (500V) DIN 51953 (500V)	>2.5 X 104~<106Ω	2.5 X 104~106
		>2.5 X 104	>2.5 X 104 ~ <8.3 X 105Ω
Electrostatic Propensity (=Static Generation)	AATCC 134 With heel grounders	-	<20 volts
Static Decay	Federal Test Method 101B Method 4046 at 15% Relative Humidity	< 0.5 sec	<0.01 sec
OTHER PROPERTIES
CEN Classification	DIN EN 685		Class 34 + 43
Composition of Material	ASTM F 1700 Certificate of Compliance		Homogeneous
Thickness	ASTM F 386, DIN EN 428	as specified ±0.005 in. (.125)	.125
Nominal Sizes	ASTM F 536, DIN EN 427	±0.016 in./lin. Ft (0.4mm/304.8 mm)	12" x 12", 24" x 24"
Squareness	ASTM F 540	maximum 0.010 in. (0.25 mm)	<0.010"
Residual Indentation	ASTM F1914 DIN EN 433	average less than 8%, max. single reading 10%	< 7%
Flexibility	ASTM F 137	no crack or break	No crack or break
Dimensional Stability	ASTM Fed. Std. No. 501a Method 6211, DIN EN 434	<0.020"/ft (0.51 mm/304.8 mm)	<0.015"/ft
Resistance to Chemicals	ASTM F 925 DIN EN 423	No more than a slight change in surface dulling, surface attack or staining	no more than a slight change in surface dulling, surface attack, or staining
Resistance to Heat	ASTM F 1514	∆<8 ave., max	<∆E=2.0
Resistance to Light	ASTM F 1515	∆E<8 ave., max	<∆E=6.0
Static Load Limit	Modified ASTM F 970-00	-	>2,500 psi
Smoke Density	ASTM E 662	<450	<450
Flame Spread	ASTM E 84, NFPA 225	<75	<75
Fire Resistance	DIN 4102		B1
Critical Radiant Flux	ASTM E 648, NFPA 253		>1.08 W/cm2(class I Interior Floor Finish, NFPA Life Safety code 101)
Abrasion Resistance	ASTM D 1044, CS-10-F Wheel, 500Gm Weight		Cycle 10,000 % Gauge Loss 1.60
Resistance to Wear	DIN EN 660-1		M
Effect of Castor Chair	DIN En 425		No Damage
Color Fastness	ISO 105 B02		At least 6
Standard for Health Care Faculties	NFPA 99		Confirms to the requirements of NFPA 99 in effect at the time of installation
Fulfils product requirements	DIN EN 649		yes
Underwriters Laboratories	UL 779		Meets UL Standard
WARRANTY
Free from defects in Workmanship and materials*			Five Years, Optional Lifetime
Conductivity*			Lifetime

Note: The resistant testing as listed below was performed on site and in accordance with the industry accepted standards of EOS-ESD 7.1 at a recent install at client facility.  The ElectraTile ESD Floor Covering was allowed to cure 48 hours prior to testing.  Installation substrate: new, cured concrete utilizing our conductive liquid adhesive and recommended grounding procedures.   Various conditions such as substrate, grades,  and humidity levels may somewhat alter the reading you receive at your facility.

Electrical Properties