United SCP: The number one most respected name in ESD Carpeting PERIOD!
ESD Carpet, ESD carpeting Installation and Grounding UltraTech and Circuit CG conductive carpeting provides an electrically conductive pathway from a person to ground allowing static electricity to be discharged without harming sensitive electronics. In high tech environments (such as networked offices and control towers) static can devastate electronics' causing a variety of "glitches" and blown components required for critical applications. Static control is of such importance in electronic assembly environments, that technicians routinely wear static control shoes or foot grounding devices (in combination with the installed flooring) to provide intimate skin to floor contact and the ultimate in static protection. United SCP Carpeting is Engineered to also control the electrostatic charge generation of rolling equipment such as carts, chairs, test equipment and transport means of subassemblies or completed product. At United SCP we have a variety of ESD flooring materials, however ESD Carpet tiles provide a crisp modular look, can be removed and replaced (when stained or worn) and can be fitted around equipment easier than our anti-static broadloom. When installing remember that static control flooring is an integral component of the clients production reliability, thus the proper installation is important! Utilizing conductive filaments interwoven with a 100% solution dyed nylon and tufted, dense pattern textured loop, this ESD carpeting provides the utmost in overall performance. This superior manufacturing technology provides a carpeting than never requires chemical anti-stat treatments yet provides exceedingly consistent electrical conductivity across the entire surface of the material. Make sure that the sub-floor and site conditions meet your requirements! The installation of United SCP carpet tiles shouldn't begin until the work of all other trades (especially overhead trades) has been completed. The installation area must be clean, fully enclosed, weather-tight and have the permanent HVAC system set at a minimum of 68o F (20o C) for a minimum of 72 hours prior to, during and after installation. United SCP Carpet Tiles must be delivered to the installation area and allowed to acclimatize to the final environmental conditions of the install area for a period of 72 hours prior to installation. To allow for proper inspection of the substrate, installation of the flooring and final inspection of the install, all areas to receive flooring must be adequately lighted. Wood floors should be of double construction with a minimum thickness of 1 inch. The wood floor must be rigid, free from movement and have at least 18" of well ventilated air space below. Typically, United carpet tiles shouldn't be installed over wooden sub-floors built on sleepers over, on or below grade concrete floors without special considerations. Contact us if such a install is required. Our recommended adhesives bond to a variety of substrates! The subfloor to receive the flooring should be smooth, flat, level, permanently dry, clean and free of all foreign material such as dust, paint, grease, oils, solvents, curing and hardening compounds, sealers, asphalt and old adhesive residue. The concrete must have a minimum compressive strength of 3500 psi. Patch and repair minor cracks and other imperfections with a Portland-base patching compounds. Do not install floor coverings over gypsum-based leveling or patching compounds. It is essential that calcium chloride moisture tests be taken on all concrete floors regardless of the age or grade level. One test should be conducted for every 1000 sq. ft. of flooring (minimum of 3). The test should be conducted around the perimeter of the room, at columns and where moisture may be evident. The moisture emission from the concrete must not exceed 5.0 lbs per 1000 sq 'ft. in 24 hours (for our ElectraTech 2450 conductive liquid adhesive) and 3.0 lbs per 1000 sq/ft for our textile reinforced releasable adhesive tape or our US C2K R Liquid Releasable Adhesive System. A diagram of the area showing the location and results of each test should be submitted to the Architect, General Contractor or End User. If the test results exceed the limitations, the installation must not proceed until the problem has been corrected. Insure that the received materials meet your criteria! Prior to installation of these products insure that all floor covering materials and adhesive have arrived on site, that the dye lots and part numbers match the clients order and that the materials have arrived in undamaged condition. Note: Allow the materials time to acclimatize to the temperature controlled environment of the installation area for at least 72 hours prior to beginning the install.
Our Adhesives bond to the impossible! Curing just takes a little longer! As mentioned earlier we have three types of conductive adhesives recommended for use with UltraStatic Control Carpet Tiles. These adhesives are designed to provide a "equiplane of conductivity" between the insulative substrate and the conductive carpeting. Chances are that your client has previously picked the adhesive when ordering the flooring material. When quoting install cost it's always best to ask about their selection. Following are the advantages and specific nuances of each:
2) Releasable Adhesive Application: Grasping inside tube of roll, walk backwards (with light tension on roll), peeling off "run." Align with any adjacent (previous) runs. Note: Although runs can be overlapped it's easiest (for liner removal purposes) to leave a slight 1/16 gap between runs). When comfortable with positioning, lightly broom in place (to remove any excessive bubbles). Remove top liner from sheet, observe carpet lay direction (arrow on carpet tile vinyl backing), place tiles on adhesive surface (starting at inside corner and carefully aligning edges). Note: Do not compress. Upon completion roll in place with 75# Roller. Floor may be used immediately!
Do Not Compress carpet tiles into place! Slight seams may be evident but blend after vacuuming and usage. 3) Our liquid conductive adhesives are solvent free, water based, one part and specifically for use with our conductive flooring materials. Perfect for raise flooring applications and other installations requiring the flexibility of carpet tile replacement combined with the high bond strength. For more information on our unique patented adhesives please visit: US C2004 Releasable Adhesive After installation: If required, carpeting may be cleaned using standard methods and procedures. Vacuuming is all that is typically needed. When required, a "dry" carpet cleaning method is recommended however wet extraction may be used. Do not use a wet extraction method prior to liquid adhesive achieving full cure (72 to 96 hours) and do not over saturate carpeting when wet cleaning. Do not apply any type of carpet protectant (stain or dirt repellants) as this may change the electrical conductivity of material.
Hopefully the electricians and other trades have stayed out of your way during the install ;) Don't hesitate to give us a call if you have questions, comments or if you run into any snags. We're here to help!
|
1)
