|
|
.\
|
ElectraGloss
High Gloss Sealer for ElectraGuard ESD Epoxy Floor Paint |
 Perfect for use With ElectraGuard ESD Epoxy
Flooring.
Outstanding
results on ElectraGuard Epoxy Floor Paint
Eliminates
nuisance static generation
from
Garland and Stonehard Epoxy Flooring
ElectraGloss conductive sealant features the addition of 316
micro-spherical stainless steel in concert with conductive urethanes to
provide exceptional
wear resistant protection and easy cleaning of
ElectraGuard ESD Epoxy.
ElectraGloss may also be used for elimination of
nuisance static generation encountered with Garland and Stonehard
standard epoxy flooring.
ElectraGloss is designed as a
semi sacrificial coating. ElectraGloss also features excellent recoatability and (in the case of aggressive contamination) may be
removed (with effort) and re-applied. ElectraGloss is designed for mop
on applications of 2 to 3 coats and is a perfect substrate for
high speed polishing.
for an incredible
luster). |
ElectraGloss
Sealer
ONLY from United SCP
Enhances aesthetics, wear resistance and cleanability.
APPLICATION & MAINTENANCE
ElectraGloss is recommended for applications on Stone Hard and Garland
standard Epoxy and fully cured ElectraGuard ESD Epoxy (minimum curing
time of ElectraGuard is 3 days at > 60 Deg F with adequate air movement)
and in relative humidity conditions of < 50%. Thoroughly remove loose
dirt and dust via sweeping (do not use sweeping compounds). Remove
imperfections if any (such as bubbles and splatters) from ElectraGuard
via light scraping followed by vacuuming . Agitate ElectraGloss sealant
in container prior to use, pour into clean contaminant free bucket and
mop on one thin even coat using non linting synthetic finish mops.
Allow coat to dry (depending on humidity and temperature) for 60 to 90
minutes before re-application of second coat. Two coats are recommended,
three coats are optimal.
Effective recoating may be
achieved in the following manner: Vacuum the floor to remove any loose
dirt or dust. Wash the floor with
ElectraClean
to remove dirt and soil, allow to dry thoroughly. Apply thin even coats
using a lint free finish mop. Allow ElectraGloss to dry for
approximately 90 minutes between coats and before resumption of foot
traffic. Allow to dry 24 hours prior to resumption of heavy rolling
loads
ElectraGloss High Gloss Routine Maintenance Procedure
ElectraGloss sealer
is an extremely durable sealer.
After application and curing of ElectraGloss routine maintenance (to
be expected with any floor) is all that is required to maintain the
luster and conductivity of the finish. It's important to remove
abrasives that can scratch and degrade the conductivity by dust
mopping (usually on a daily basis). On an occasional basis (most of
our clients prefer to do this once a week) wet mop the floor with a
diluted mixture of
ElectraClean and water and allow to dry. ElectraClean works
great with power scrubbing equipment OR in hand mop applications.
ElectraClean removes dirt and abrasives that dry mopping leaves
behind and smells great too.
Note: Do not wash your
ElectraGloss ESD Floor sealer for at least 48 hours after
application and NEVER wash ElectraGloss with plain water (always use
ElectraClean diluted with water) for damp moping.
SAFETY
INFORMATION
|
Health |
1 |
|
Flammability |
0 |
|
Reactivity |
0 |
|
Personal
Protection |
B |
|
Nonvolatile Solids |
20 + |
| Total
Active |
26% |
|
Static Dissipation |
0.02
Second |
| pH
|
8.4 -
9.0 |
|
Gloss 60 |
80+ @
3 coats |
| Color |
Translucent white |
|
Weight Per Gallon |
8.55
- 8.8 |
| Slip
Resistance (ASTM) |
0.65
Minimum |
|
Stability |
1
year minimum
at room temperature |
|
Freeze/Thaw Stability |
3
cycles minimum |
|
Drying Time |
60-90 minutes |
|
Chemical
Resistance |
Good |
|
Gallon Coverage (Feet 2 ) |
1500
- 2000 |
|
Removability (Gardner) |
75
cycles maximum |
|
This material is not a hazardous
mixture, as defined in 29 CFR 1919, 1200 and M.G.L. c. 111F. Safety glasses
and gloves should be worn during application and handling. If ingested drink
milk, water, or fruit juice and induce vomiting with oil of ipecac. In the
event of eye contact flush area with water for 15 minutes.
Contact a Physician. For detailed information consult MSDS sheet. |
Ordering Info:
-
1 gallon: PN E-Gloss 1, $49.90 ea,
weight 10 lbs
-
1 case (4 x 1 gallon) PN E-Gloss
4, $199.66 ea, weight 38 lbs
-
5 gallon container, PN E-Gloss 5,
$249.02, weight 45 lbs
-
Typical coverage: 1,500 to 2,000 SF per gallon per coat
MSDS SHEET
WARRANTY
PRINTER
FRIENDLY CUT SHEET FOR DISTRIBUTION
Call for
Large Volume Pricing and SAVINGS!
And visit us for these other fine
ESD Floor maintenance Chemicals.
|
CONTACT
United STATIC CONTROL PRODUCTS!
United Static Control Products
P.O.B. 19252, 4878 Lake View Circle
Colorado City, CO 81019
United States of America
Phone: 719 676
3928 Fax: 719 676 3929
24/7
Tech Support (customers only)
719
676 3928 (option 8)
Major Credit
Cards Accepted
ESD
Flooring,
Mats, Chemicals,
ESD Ionizers, and
Expertise
United SCP Tames the Static Beast BEFORE it Takes Another Byte
This page last updated on
05/10/2010
|
|
